Ceramic sleeve lined Pipe

The ceramic tube or ceramic sleeve sintered as a whole part, and then assemble it into the steel pipe with our high-strength-temperature-resistant epoxy adhesive.

The ceramic sleeve lined pipe has a smooth inner wall, excellent tightness as well as good wear and chemical resistance ability.

Alumina ceramic sleeve lined pipe with flange

Ceramic sleeve lined pipe with flange

Ceramic sleeve lined reducer

Alumina ceramic sleeves lined pipe

Alumina ceramic sleeve lined pipe export to australia

95% alumina ceramic sleeve lined pipes, elbows and T pipes have been largely applied in lithium battery material conveying system in recently years.

Wear abrasion stainless ceramic pipes with below advantages:

Better purity for inside and outside pipe materials;
More abrasive;
Higher corrosion resistance;
Stronger impacting resistance;
Better high temperature resistance
Smaller flatness of inside pipe(ceramic flatness≤0.5mm)

In addition, the flatness of ceramic casing is also an important factor affecting the size of lithium battery materials.We did a lot of analysis and improved our manufacturing techniques to solve both of these problems.Now it can help lithium battery delivery systems better solve these problems, with better material purity, longer service life and better economic benefits.

For the convenience of customers, are to provide a more specific process is as follows:

Removing rust and decontamination process of outer-layer steel pipe;
Must be in strict accordance with the prescribed ratio, the binder a\b accurate measurement, with how many, must be stirred evenly, full stir-mixing must not be less than 4 times, such as adding a mixture of the embedded feed should be mixed with the binder and then add the mixture to stir up not less than 3 times;
The binder is applied evenly on the inner wall of the steel tube to ensure the thickness is not less than 0.5mm thickness. Then apply the binder on the outer surface of the ceramic ring to ensure the thickness between the 0.5mm-1mm. Also in the ceramic ring side (with the ceramic ring contact with the corresponding surface) Daub 0.5mm Adhesive, to ensure that after the installation of the ring and the seal between the ring;
After the installation of the ceramic ring in place, it is necessary to repair the gap between the assembled ceramic rings and mend the joints to ensure the sealing between the ring and the ring;
According to the NPT standard, we process the two pipe ends of male and female thread processing. The end of the pipe processing, and processing 1x45° groove, to prevent on-site installation in the process of cutting the hands of construction workers, do a good job of safety protection measures, thread processing, need to brush oil to protect the thread;
After installing the ceramic ring, check the internal surface of the ceramic ring of the formation, finishing in place, cannot move the position of the pipe, because the binder is not dry, vibration is easily caused by the displacement of ceramic rings, affect the use of the effect of cold weather in winter, binder drying time is longer, need to ensure more than 48 hours.

Relevant technical introduction of wear-resistant ceramic ring

The wear resistant ceramic ring is a special kind of ceramic with Al₂O₃ as the main raw material and the rare metal oxide as the flux, which is melted by high temperature at 1700 ^oC.

Ceramic lined inner details

99.7% Alumina ceramic tube/high frequency ceramic is our main product. We are making High quality alumina furnace tubes.

99.7% alumina is the main material, 85% and 95% alumina tubes also available.

Features：

The wear-resistant ceramic ring has the characteristics of smooth interior wall and super wear resistance. Widely used in chemical, fine powder conveying pipelines and other industries, with high wear-resistant and anti-corrosion functions.
In accordance with the traditional process, the production of wear-resistant ceramic ring is mainly the use of hot-pressing casting or grouting molding. Adopting isostatic pressing forming technology, the ceramic ring with isostatic pressing is better in compactness and more accurate in ceramic size.
At present, our ceramic ring lining pipeline in the silicone industry, chemical industry, fine powder conveying industry has been widely used.

Sleeve Type Expansion Joints

Sleeve Type Expansion Joints are primarily designed to compensate for thermal expansion but it is not the only movement being imposed on the pipeline system. Other types of movements can occur that need to be taken into account when providing a pipework flexibility solution such as building settlement, wind loading, vibration from rotating and reciprocating machinery. Related Ceramic lined pipe Ceramic lined pipe is made through self-propagating high-temperature synthesis (SHS) technique. The sleeve type expansion joint is also called tube compensator, pipe expansion joints, which is used for hot fluid pipelines, mainly applied to the laying of straight pipelines. And the working medium can be hot water, steam, oil, etc. The sleeve expansion joint does thermal expansion by sliding its external sleeve. Sleeve compensator Types of Sleeve Type Expansion Joint: Buried sleeve expansion joint: Using advanced sealing structure and sealing materials with the features of easy installation...

Sleeve Type Expansion Joints

Sleeve Type Expansion Joints are primarily designed to compensate for thermal expansion but it is not the only movement being imposed on the pipeline system. Confirmed and drawing by our engineer Other types of movements can occur that need to be taken into account when providing a pipework flexibility solution such as building settlement, wind loading, vibration from rotating and reciprocating machinery. The sleeve type expansion joint is also called tube compensator, pipe expansion joints, which is used for hot fluid pipelines, mainly applied to the laying of straight pipelines. And the working medium can be hot water, steam, oil, etc. The sleeve expansion joint does thermal expansion by sliding its external sleeve.

Tubes Erosion Shields

Tubes Erosion Shields are used to reduce excess wear of boiler tubes within the extreme conditions prevalent inside a fossil fuel fired boiler, Sunny Steel is able to manufacture and supply erosion shield solutions to protect and reduce wear in all applicable boiler related situations. Boiler Tube Shields are designed to eliminate major maintenance and downtime costs from boiler and condenser tube failure. Advantages Tube Shields are custom made to fit perfectly to straight sections, curved sections and even finned and specialised tubing. Boiler Tubes Erosion Shields, also known as anti-corrosion Shields, anti-wear plate, anti-wear protection Shields, anti-wear cover plate, anti-corrosion cover plate, boiler climbing pipe, anti-wear pressure plate, etc. , which are used in combination with snap rings. Boiler Tubes Erosion Shields are produced using a high-pressure press and professional mold pressing. The production time is short, the welding performance is good, the welding should not...

Cast basalt lined steel pipe

Cast basalt lined steel pipe is consist of steel pipe, cast basalt pipe and the concreteness of cement mortar. The excellent performance of cast basalt lined steel pipe is that it sets tenacity of steel pipe, abrasive resistance of cast basalt pipe, concreteness of cement mortar in one. After 30 years of practical use proved cast basalt lined steel pipe is a reliable and effective combination of wear—resistant materials. Be used in a variety of transportation of corrosive materials in working condition. This greatly improves the products adaptive capacity in complicated operation conditions. At the same time. cement mortar is selected as the filling material and this can make the inside surface of steel pipe in alkali mediums. So the surface of steel pipe generates purifying films. These films can prevent being rusted. Flange connection is one kind of common pipeline installation connections. The parameters of the outside steel pipe will be decided according to the working pressure of ...

Large diameter ceramic lined tile pipe

The Ceramic tile lined pipe spool is composed by steel pipe, adhensive and abrasion-resistant ceramic, we use 20 # seamless steel pipes shaping with hot bending (it is different from centrifugal casting or steel plate rolling), the ceramic tiles bonding with GWJ-350 high temperature-resistant inorganic adhesive which was developed by TsingHua University and affix abrasion-resistant ceramic in the steel pipes, we use miss match installation instead of directly bonding (this technology was used in the bridge building a thousand years ago), and forms a firm wear-resistance layer after heating solidification. Ceramic tile lined pipe spool is applicable for the pneumatic powder-feeding, and can be used under a temperature of 350℃without aging and peeling for long life. The service life is 4-5 times than the normal abrasion-resistant pipes. Advantage Super wear-resistant, high density: we use 95% of chromium corundum, 100 tons dry-pressing. Elbows formed by hot-bending, the outside of ...

To help you understand the main features of the wear-resistant composite ceramic pipe

The pipeline is a product that has been developed in recent years. This product has received attention from all aspects. It has a unique advantage of its own. It has been firmly established. Wear self propagating ceramic composite pipe is adopted self propagating ceramic composite pipe aluminum material by centrifugation, heat spreading sintering, because of its good abrasion resistance, water resistance, good corrosion resistance and become one of the many projects in the pipeline wear preferred products, self propagating ceramic composite pipe is easy to break and fall but the manufacturing process the traditional production, and the existence of micro crack, has certain influence on the wear resistance of the process, using the international advanced technology of nano materials, add special additives in traditional ingredients, and the sintering temperature to 2800 DEG C (pressurized aeration technology), SHS products, high strength, small micro crack good toughness, not easy to fa...

Ceramic lined pipe expansion joints

Ceramic lined pipe expansion joints are designed to safely absorb the dimensional changes of pipework systems and ducts caused by heat induced expansion and contraction. They are essential in pipework systems that are used to convey substances of a high temperature, such as steam, heated water or exhaust gases. Expansion joints can also be designed for other applications, such as noise and vibration caused by reciprocating machinery, building settlement and in some extreme environments earthquake movement. Expansion joints are very important components with in a pipework system as they not only solve the problems associated with pipework movement but offer such advantages as reducing stresses and loads to connecting equipment such as pumps and steam turbines.

Wear Resistant Pipeline in Power and Cement Plant

1.Cement Industry: Cement powderchoosing transmission pipeline, feed hopper, chute, feed bin and so on. 2.Electricity Industry: Coal power plant coal transmission pipeline, fly ash exhaust system, chemical water circulation system, desulfurizing system and all the corrosive areas in the nuclear electrical power plant. 3.Coal Mine Industry: Coal powder, coal water slurry transmission, the air supply system, air exhaust system and drainage system of the mine. 4.Chemical Industry: High corrosive medium transmission, such as strong acid and strong alkali. Salt chemistry brine, salt slurry, raw salt transmission. 5.Petroleum Exploitation Industry: Raw oil transmission, natural gas collection transmission system, waste water recirculation system and so on. 6.Metal production Industry: Transmission of coke powder, mine powder, pulp, smelting waste and so on. 7.Mining Industry: Pulp transmission pipeline, the air supply system, air exhaust system and drainage system of the mine. 8.Dredging Pro...

Ceramic lined pipe

Search This Blog