Skip to main content

UHMWPE wear pipe


Ultra-high molecular weight polyethylene (UHMWPE) is a new kind of engineering thermoplastics with more than 3 million viscosity-average molecular weight. Ultra-high molecular weight polyethylene pipe has superior performance over conventional HDPE pipe such as very high wear resistance, impact resistance, excellent resistance to internal pressure strength, resistance to environmental stress cracking, intrinsically self-lubricating, anti-adhesion, low temperature resistance and excellent chemical resistance.

Ultra-high molecular weight polyethylene (UHMW-PE) is the role of special catalyst, polymerization of viscosity-average molecular weight greater than 2.5 million engineering thermoplastics . Ultra high molecular weight polyethylene pipe with high wear resistance, friction coefficient is extremely small , impact resistance , corrosion resistance, non-scaling , the excellent anti- pressure strength , resistance to environmental stress cracking resistance, good self-lubricating , anti-stick attached , unique low temperature resistance , excellent chemical stability, superior performance , is the most cost-effective pipeline was wearable , long-term at -269 degrees to +80 degrees working conditions , are widely used in metallurgical and mining beneficiation , power plants, grain silos , acid and alkali transport , tailings, slurry and coal transportation , terminals, shipyards, oil, natural gas , textiles, paper , food, chemical , mechanical, electrical and other industries.

    Can be a lot of use in wastewater treatment , pipelines , there are pipeline external corrosion requirements for long-distance transmission of great significance ; due to the thermal conductivity of this pipe is not ten thousand times smaller pipe , can greatly reduce the cost of transporting pipe insulation for the winter in cold regions and transportation of crude oil and other materials are of great significance , can be replaced by stainless steel, wear-resistant alloy tube , plastic composite pipe and other special pipe.

1 wear characteristics
Ultra-high molecular weight polyethylene pipe molecular weight of up to 250 million more than the tube , the friction coefficient is extremely small , it has a high resistance to sliding friction capability. Wear six times higher than normal alloy steel , stainless steel, 29 times . Is 19 times the phenolic resin , nylon six seven times , five times polyethylene , greatly improve the life of the pipeline.

2 the corrosion resistance
UHMW-PE is a saturated molecules structure, so its high chemical stability, corrosion resistance of the product can be harsh chemicals , strong acids except for some slight corrosion at high temperatures , as in other lye , acid in from corrosion. Can be used in a concentration of less than 85% of concentrated hydrochloric acid at a concentration of less than 80% sulfuric acid , nitric acid concentration of less than 20% of the performance is quite stable.

3 anti- impact resistance
In the existing engineering plastics highest impact toughness of ultrahigh molecular weight pipeline , many materials in serious or repeated shock of the explosion would crack , damaged, broken or surface stress fatigue . The product according to GB1843 standards, Izod impact test without damage, and strong to withstand external shocks, internal overload and pressure fluctuations.

4 self-lubricating
Since the ultrahigh molecular weight polyethylene tube containing a waxy substance , and good self-lubricating . Friction coefficient (196N, 2.5 hours) only 0.217MN / m (GB3960). Oil lubricated sliding properties than their steel or brass . Especially in harsh environments , dust, sand and more places , the product itself more fully dry lubricating properties displayed . Not only freedom of movement and protection of related artifacts do not wear or strain.

5 low temperature resistance
Ultrahigh molecular weight polyethylene pipe excellent in low temperature resistance , impact resistance , abrasion resistance of minus 269 degrees when substantially constant . Is a kind of plastic is currently the only operating at near absolute zero temperature. Meanwhile, the optimum temperature of UHMWPE pipe width , long-term work at a temperature of -270 ℃ to 80 ℃ .

6  easy scaling of
Because of ultra high molecular weight polyethylene pipe friction coefficient is small and non-polar , so it has good adhesion to the surface of non- pipe finish . Existing materials in general PH value of 9 or more media in both scale , ultra-high molecular weight polyethylene pipe is not scaling, this feature is used for the power plant fly ash system has great significance. In crude oil, mud and other pipelines is also very applicable .

7 long service life
UHMWPE molecular chain unsaturated genes less fatigue strength of more than 50 million times , optimal resistance to environmental stress cracking resistance , resistance to environmental stress cracking > 4000h, is more than 2 times the PE100 , buried about 50 years of use , still maintain more than 75% of the mechanical properties.

8 easy to install
Ultra-high molecular weight polyethylene (UHMW ---- PE) pipe unit pipe length accounts for only one-eighth the weight of steel , making loading and unloading, transportation, installation more convenient , and can reduce labor intensity of workers , UHMW-PE pipe aging resistance strong , 50 years aging. Whether on the ground erection, or can be buried underground . When installing either welded or flanged connections are safe, reliable, convenient , no corrosion, saving labor , which fully reflects the use of ultra high molecular weight polyethylene pipe "energy , environmental, economic , and efficient" superiority.

9 other features
Ultra high molecular weight polyethylene pipe can still suck , suck noise , antistatic, electronic shielding capability , non-absorbent , light weight, easy machining , coloring and other prominent features.

Related products

Sleeve Type Expansion Joints

Sleeve Type Expansion Joints are primarily designed to compensate for thermal expansion but it is not the only movement being imposed on the pipeline system. Confirmed and drawing by our engineer Other types of movements can occur that need to be taken into account when providing a pipework flexibility solution such as building settlement, wind loading, vibration from rotating and reciprocating machinery. The sleeve type expansion joint is also called tube compensator, pipe expansion joints, which is used for hot fluid pipelines, mainly applied to the laying of straight pipelines. And the working medium can be hot water, steam, oil, etc. The sleeve expansion joint does thermal expansion by sliding its external sleeve.

Ceramic Tile Lined Bend

Ceramic tile lined bending have very uniform coating of specially formulated ceramic material that is affixed to the inner of the pipe and gives a very smooth surface. It is well understood that conveying velocity of ash, its density as well as size of ash particles are major factors that determine wear rate of Bends and Y-Pieces. Here, the use of Alumina Ceramic in Ash Handling systems help in lowering the possibility of wear and damages caused to the internals. Here, our expertise lies in filling the linings in casings manufactured at our works or can also be fitted directly in worn out volute casing at plant site. Well package of Alumina Ceramic Lined Bends Some of the industry areas where these are used include: Coal Fired Thermal Power Projects Mineral processing units Steel Plants Cement Plants Coal and Mineral washeries Aluminium plants

Ceramic lined pipe elbows

Ceramic - lined pipe  is the use of SHS – Manufacturing centrifugation, the melting point of alumina  ceramic  pipe in 2045 ℃, alumina layer and the steel layer

Sleeve Type Expansion Joints

Sleeve Type Expansion Joints are primarily designed to compensate for thermal expansion but it is not the only movement being imposed on the pipeline system. Other types of movements can occur that need to be taken into account when providing a pipework flexibility solution such as building settlement, wind loading, vibration from rotating and reciprocating machinery. Related  Ceramic lined pipe Ceramic lined pipe is made through self-propagating high-temperature synthesis (SHS) technique. The sleeve type expansion joint is also called tube compensator, pipe expansion joints, which is used for hot fluid pipelines, mainly applied to the laying of straight pipelines. And the working medium can be hot water, steam, oil, etc. The sleeve expansion joint does thermal expansion by sliding its external sleeve. Sleeve compensator Types of Sleeve Type Expansion Joint: Buried sleeve expansion joint: Using advanced sealing structure and sealing materials with the features of easy installation...

Stainless carbon steel composite pipe

The stainless carbon steel composite pipe is made of stainless steel and carbon structural steel. Stainless steel, with its excellent corrosion resistance, abrasion resistance, heat resistance, and its shiny, luxurious surface, and are widely used in various fields of the national economy. Lack of limited by the resources of our NI, relies heavily on imports of stainless steel demand, the price is more expensive, the popularization and application of stainless steel to a certain extent by with constraints. Carbon steel, especially the Q series carbon structural steel, with high bending strength, good impact resistance and anti-fatigue limit, as well as low prices, thus making it the basis of the national economic construction materials, carbon structural steel, its main elements Fe metal reactivity, oxidation in the atmosphere, it is easy to rust, let alone in a corrosive medium or special (wet, dark) environment. Year for its anti-corrosion investment as well as economic losses becaus...

Large diameter ceramic lined tile pipe

  The Ceramic tile lined pipe spool is composed by steel pipe, adhensive and abrasion-resistant ceramic, we use 20 # seamless steel pipes shaping with hot bending (it is different from centrifugal casting or steel plate rolling), the ceramic tiles bonding with GWJ-350 high temperature-resistant inorganic adhesive which was developed by TsingHua University and affix abrasion-resistant ceramic in the steel pipes, we use miss match installation instead of directly bonding (this technology was used in the bridge building a thousand years ago), and forms a firm wear-resistance layer after heating solidification. Ceramic tile lined pipe spool is applicable for the pneumatic powder-feeding, and can be used under a temperature of 350℃without aging and peeling for long life. The service life is 4-5 times than the normal abrasion-resistant pipes. Advantage Super wear-resistant, high density: we use 95% of chromium corundum, 100 tons dry-pressing. Elbows formed by hot-bending, the outside of ...

Backpack wear-resistant ceramic lined elbow

Backpack wear-resistant ceramic lined elbow are used for connecting pipes of different diameters and find wide applications in various chemicals, construction industries, paper, cement & ship builders. Connect the unit in process SunnySteel's Backpack wear-resistant ceramic lined elbow and avoids product attrition.It reduces considerabley degradation of conveyed material and avoids formation of angel hair through its patented deflection chamber. Backpack wear-resistant ceramic lined elbow for Pneumatic Conveying Tubes and bends in pneumatic conveying lines are suffering more or less abrasion. SunnySteel's ceramic lined pipes resists abrasion and avoids product attrition.It reduces considerabley degradation of conveyed material and avoids formation of angel hair through its patented deflection chamber.The compact design reduces cost of pipe support and installation. It is automatically self-purging with little pressure drop. Ceramic Lined Elbows and Bends could be also appli...

The ceramic lined pipe

 The ceramic lined pipe is a high performance pipe consisted of ceramic ring,seamless steel tube and adhesion agent. Ceramic lined pipes and fittings like ceramic bend,reducer and tee are manufactured by Sunny Steel . These ceramic lined system can provide excellent structural support and wear resistance,they are widely used in the heavy industries' most difficult wear situation. Features & Benefits: The lining of the product is manufactured from alumina ceramics for engineering.Alumina ceramic material have a high hardness ,and have a strong wear resistance. As the amphoteric compound ,the engineering ceramics will not chemically react with acid and alkali. Since the density of the ceramic is just half that of the steel,the weight of the custom ceramicpipes and fittings is light,which contributes to easy installation. 10 to 1 life performance ,reducing the maintenance cost , down time and clean up. Application: Replace cabon steel ,stainless steel and S...

Get to contact us

Name

Email *

Message *